robotics

Img

Description: Robotics is the branch of mechanical engineering, electrical engineering and computer science that deals with the design, construction, operation, and application of robots, as well as computer systems for their control, sensory feedback, and information processing.

  • Img

    Robotic ARM Kit Pick and place robot is the one which is used to pick up an object and place it in the desired location. It can be a cylindrical robot providing movement in horizontal, vertical and rotational axes, a spherical robot providing two rotational and one linear movement, an articulate robot.

  • Img

    Robotic Assembeled RDY kit Description: Chasis + Two 60 RPM DC Geared Motor + Castor Wheel

  • Img

    CLAMPFor DC Geared Motor. Clamp is act like a physical support for robots.

  • Img

    CLAMPFor DC Geared Motor. Clamp is act like a physical support for robots.

  • Img

    DC Geared Motors A geared DC Motor has a gear assembly attached to the motor. The speed of motor is counted in terms of rotations of the shaft per minute and is termed as RPM .The gear assembly helps in increasing the torque and reducing the speed.

  • Img

    L293D Motor Drive The L293D is a popular motor driver IC that is usable from 6 to12V, at up to 1A total output current. By itself, the IC is somewhat difficult to wire and use, but the Compact L293D Motor Driver makes it much more convenient to use.

  • Img

    L298 Motor DriveThe L298 is a popular motor driver IC that is usable from 6 to 50V, at up to 4A total output current. By itself, the IC is somewhat difficult to wire and use, but the Compact L298 Motor Driver makes it much more convenient to use.

  • Img

    ULN2803 Drive ULN2803 Stepper Motor Driver Module:Description: 8 Darlington Arrays in 18-Pin DIP, Perfect for running relays and high-power devices up to 500mA and up to 50V, Package part # ULN2803A.

  • Img

    STA Drive Board - 4A Description: STA401A is a NPN Darlington 4 Channel drive Specification Given Below. Max Current 4 Amps. Very easy to drive Stepper Motors, Relays, DC Motors, DC Solenoids, Actuators.

  • Img

    DC Motor Speed Control / LED Dimmer The speed control of DC motor is very crucial in applications where precision and protection are of essence. Purpose of a motor speed controller is to take a signal representing the required speed and to drive a motor at that speed. MC's can provide easy control of DC motor.

  • Img

    Stepper Motor Drive - Max Load 20KG - 2Amps The Stepper Motor Chopper Driver is a Bipolar Stepper Motor Drive with easily adjustable current control up to 2A and 20 kg, based on SGS-Thompson L297 and L298 stepper motor controller and driver IC's. Stepper motors are rated by current and not by voltage.

  • Img

    TB65603A Micro Stepper Motor Driver Board Featurs: supply voltage DC 10V-24V, Toshiba TB6560A controller, High speed opto-couplers, Low voltage, over heating, Excitation modes: 1/2, 1/8, 1/16 step, Large passive heat-sink., Dimensions: 50 x 75 x 35 mm etc.,

  • Img

    Micro Stepper Drive Description:This stepper module with neat layout and steady good performance is based on TB6560AHQ chip by TOSHIBA. It can run max current of 3.5A and 16 micro-steps. Current is adjustable step by step. Onboard we have half/full current for our selection.

  • Img

    Castor Wheel-Steel Ball caster wheel is an omni directional wheel This wheel can be used as neutral wheel for the robot. Specification: Base plate diameter -27.5mm, Caster wheel diameter - 13.5mm, Wheel height - 18mm, Mounting hole - Three, 120 degree apart, 3mm or 1/8 inch diameter.

  • Img

    Servo Motors -SG 90 A servomotor is a rotary actuator or linear actuator that allows for precise control of angular or linear position, velocity and acceleration. It consists of a suitable motor coupled to a sensor for position feedback. It also requires a relatively sophisticated controller.

  • Img

    Chasis Specification: Sheet Metal Pressed Robotic Chassis Very easy to use with Good Gauge Sheet. Ready to Fix Motors and PCB Boards. Castor Wheel for Front side fit. Dimension 16 cm Length x 12cm Width x 1.5cm Diameter for Motors Fixing.

abgroupsinfo@gmail.com